OFFICIAL NOTICE CONTENT
Opportunity description
In accordance with Federal Acquisition Regulation (FAR) 4.1102 quoters are required to be registered in the System for Award Management (SAM) at the time an offer or quotation is submitted. (i) This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation. (ii) The solicitation number is 70T05026Q5903N008. The solicitation is issued as a request for quotation (RFQ). (iii) All questions must be submitted via email to Heather Lewis at heather.lewis@tsa.dhs.gov no later than Thursday, September 17th, 2025 at 10:00 am. Eastern Time. (iv) All quotes must be submitted to the above email no later than Tuesday, September 22nd at 10:00 pm. Eastern Time. (v) The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2025-04. (vi) This acquisition is issued with a total small business set aside. The associated NAICS code is 332510 - Hardware Manufacturing. (vii) List of line item numbers and items, quantities, and units of measure: See Attachment. 1) Description of requirements for the items to be acquired: 220 � Magnetic Stanchions delivered to Miami International Airport (MIA) (viii) Delivery, acceptance, and FOB point are at the below address. ATTN: Giovanni Colon MIA Storage Facility 1336 NW 78th Ave, Doral, FL 33126 (ix) The provision at 52.212-1, Instructions to Offerors -- Commercial applies to this acquisition. There are no addenda to the provision. (x) The provision at 52.212-2, Evaluation -- Commercial Items does not apply to the solicitation. The evaluation procedures to be used are as follows: Award will be made using the lowest price technically acceptable (LPTA) selection process. Award may be made on initial quotations. Therefore, each initial quote should contain the quoter's best terms from a technical, all submission requirements and price standpoint. However, the Government reserves the right to contact quoters if it is later determined by the contracting officer to be necessary or in the government's best interests. The LPTA process will proceed as follows: 1) Quotes may be removed from consideration for, but not limited to, the following reasons: � Quotes that are not received timely � Quotes that fail to follow the instructions in FAR Provision 52.212-1 � Quotes that fail to submit ALL required documentation/provisions � Quotes that have language inconsistent with the terms and conditions set forth in the solicitation 2) Quotes will be ordered by price from lowest to highest. 3) The Government will then review Factor 1 of the lowest priced quote. If the review finds that Factor 1 of the lowest priced quote is acceptable, the Government will then evaluate Factor 2 of the lowest priced quote. If the review finds that Factor 2 of the lowest priced quote is acceptable, that quote represents the best value to the Government and the technical evaluation process stops at this point. Contingent upon a subsequent determination of price reasonableness (Factor 3) and of contractor responsibility by the Contracting Officer, an award will be made to that quoter without further consideration of any other quoters. If the lowest quote is determined not to be acceptable for any reason, then the next lowest priced quote will receive an evaluation as described above. The process will continue in order by price until a quote from a responsible contractor is determined to be acceptable and priced fairly and reasonably. 4) USING THIS PROCEDURE, THE GOVERNMENT MAY NOT EVALUATE ALL QUOTES. (e) Each Factor will be evaluated as follows: Factor 1. Technical Acceptability Technical Acceptability will be rated on an "acceptable" or "unacceptable" basis as follows: Acceptable - Quoter completes the Attachment (1) Technical Compliance Table indicating the item meets the salient characteristics specified and all SOW 2.2 requirements and provides sufficient supporting documentation to show acceptability to the salient characteristics; and submits a completed Attachment (2) Reps and Certs document or indicates compliance with the Reps and Certs statement provided in the table of Attachment (1). Unacceptable - Quoter did not complete the Attachment (1) Technical Compliance Table indicating the item meets the salient characteristics specified and SOW 2.2 requirements and/or did not provide sufficient supporting documentation to show acceptability to the salient characteristics; and/or did not submit a completed Attachment (2) Reps and Certs document or did not indicate compliance with the Reps and Certs statement provided in the table of Attachment (1). Factor 2. Price The Quoter shall provide a total price for the sample traps that meets all the requirements in SOW 2.2. Submission Requirements: All requirements must be received in order to be considered technically acceptable. -Completed Pricing schedule: Refer to the attached RFQ Fillable Requirement for structure of pricing schedule -Completed Attachment 1 � Technical Compliance Table -Completed Attachment 2 � Reps and Certs -Applicable fill in clauses and provisions located throughout the Combined synopsis and the attached RFQ fillable requirements -Supporting documentation to show acceptability to the salient characteristics (specifications sheet)
FEDERAL BUYER
Buyer and contracting office
Public points of contact
GOVBIDFIT SCREENING LENS
What deserves attention before you spend bid time
These screening signals are generated from the public notice fields stored for this specific opportunity. They are not eligibility findings or predictions; they are prompts for a faster, more disciplined review of the official solicitation.
This record is in a solicitation stage, so submission instructions, evaluation factors, attachments and amendments should be reviewed before a bid/no-bid decision.
The stored deadline is within three days. Check earlier question, site-visit and attachment requirements immediately; the final response date may not be the first deadline that matters.
Small Business Set Aside - Total is recorded as the set-aside or restriction. Confirm the bidding entity actually satisfies the applicable program and size requirements before investing proposal time.
NAICS 332510 · PSC 5660 is the recorded classification. Use it as a screening clue, then compare the actual scope and deliverables rather than treating the code alone as proof of fit.
GovBidFit stores 2 notices tied to this solicitation. Review the notice chain and official SAM.gov history because later postings can change dates, scope or instructions.
GovBidFit has stored substantive notice text for this record, but attachments, clauses, amendments and Q&A can still contain requirements that are not visible in the description alone.
The source data includes 1 public contracting contact. Use the solicitation's stated communication rules and deadlines before contacting the buyer.
Questions to resolve next
What this opportunity record tells you
SAM.gov identifies this as a solicitation from HOMELAND SECURITY, DEPARTMENT OF. The record was posted on September 14, 2026 and currently lists September 22, 2026 as the response deadline. GovBidFit keeps source facts separate from its matching guidance so you can see what comes from the federal notice.
The listed product or service classification is NAICS 332510 · PSC 5660. The set-aside field is Small Business Set Aside - Total. These fields help narrow your search, but they do not replace the full solicitation, amendments, attachments, clauses or eligibility language on the official source.
Before deciding to bid
GovBidFit is independent and is not a U.S. government website. GovBidFit stores a structured mirror of SAM.gov public opportunity data in its own database and keeps the compact snapshot as a fallback. The official SAM.gov notice remains the controlling source. The official SAM.gov notice controls if anything here differs from the source or a later amendment.
Open the official SAM.gov notice →