OFFICIAL NOTICE CONTENT
Opportunity description
Statement of Work CGC Stratton Shaft Alignment and Bearing Reaction Check Intent: contractor must measure and report to USCG the Vertical and Horizontal Loads on the (2) bull gear bearings and (2) intermediate bearings, stern and strut bearings, using the Strain Gage Method. Period of Performance: 01 November 2026 � 01 January 2027 Location: USCGC Stratton, 42 Eagle Road Coast Guard Island, Alameda CA 94501 Contractor will install a total of (5) full bridge strain gage sets on the Port shaft, and (5) strain gage sets on the Starboard shaft, to complete the bearing load calculations. Contractor will also measure and report the vertical load on each line shaft bearing using the Hydraulic Jack/Load Cell method. Contractor will provide all specialty tools and calibrated instrumentation necessary to install the strain gages and measure the strain gage data. Contractor shall provide a final written report within 15 days after completion of the work covered by this scope of work. The report shall contain at a minimum the following: Introduction and References Project description Alignment calculations Alignment tests with strain gages Conclusions Recommendation for future action Data sheets on shaft model used to obtain reported results e.g. stations, strain gauge locations, diameters, lengths, load points, etc. Data sheets from Computer runs that computed reported results e.g. stations, deflections, stresses, bearing reactions, slopes, etc. References: Coast Guard Drawings Coast Guard Drawing 750 WMSL 114-001, Rev B, Fairwaters and Rope Guard Installation Details & L/M (ASC114001) Coast Guard Drawing 750 WMSL 243-007, Rev E, Propulsion Shafting System Arrangement (ASC243008) Coast Guard Drawing 750 WMSL 243-008, Rev -, Propulsion Shafting and Appendage (ASC243001B) Coast Guard Drawing 750 WMSL 244-001, Rev -, Propulsion Shafting System Measured Bearing Reaction Report (ASC244001) Coast Guard Drawing 750 WMSL 244-002, Rev B, Stern Tube Seal & Strut Bearings Arrangement & Details & L/M (ASC244002) Coast Guard Drawing 750 WMSL 244-003, Rev -, Propulsion Shafting System Measured Bearing Reaction Report (AS2244001 Notes: For any references to be distributed, the contractor must be registered in the Joint Certification Program (JCP) through Defense Logistics Agency (DLA) and provide your JCP number to the listed point of contact for this work. For questions regarding this statement of work, contact LTJG Maximos Brady maximos.h.brady@uscg.mil
FEDERAL BUYER
Buyer and contracting office
Public points of contact
GOVBIDFIT SCREENING LENS
What deserves attention before you spend bid time
These screening signals are generated from the public notice fields stored for this specific opportunity. They are not eligibility findings or predictions; they are prompts for a faster, more disciplined review of the official solicitation.
This record is in a solicitation stage, so submission instructions, evaluation factors, attachments and amendments should be reviewed before a bid/no-bid decision.
The stored deadline is within three days. Check earlier question, site-visit and attachment requirements immediately; the final response date may not be the first deadline that matters.
Small Business Set Aside - Total is recorded as the set-aside or restriction. Confirm the bidding entity actually satisfies the applicable program and size requirements before investing proposal time.
NAICS 811310 · PSC J028 is the recorded classification. Use it as a screening clue, then compare the actual scope and deliverables rather than treating the code alone as proof of fit.
GovBidFit has stored substantive notice text for this record, but attachments, clauses, amendments and Q&A can still contain requirements that are not visible in the description alone.
The source data includes 2 public contracting contacts. Use the solicitation's stated communication rules and deadlines before contacting the buyer.
Questions to resolve next
What this opportunity record tells you
SAM.gov identifies this as a combined synopsis/solicitation from HOMELAND SECURITY, DEPARTMENT OF. The record was posted on September 14, 2026 and currently lists September 21, 2026 as the response deadline. GovBidFit keeps source facts separate from its matching guidance so you can see what comes from the federal notice.
The listed product or service classification is NAICS 811310 · PSC J028. The set-aside field is Small Business Set Aside - Total. These fields help narrow your search, but they do not replace the full solicitation, amendments, attachments, clauses or eligibility language on the official source.
Before deciding to bid
GovBidFit is independent and is not a U.S. government website. GovBidFit stores a structured mirror of SAM.gov public opportunity data in its own database and keeps the compact snapshot as a fallback. The official SAM.gov notice remains the controlling source. The official SAM.gov notice controls if anything here differs from the source or a later amendment.
Open the official SAM.gov notice →